REALFLIGHT DONGLE EMU FLAPS MANUALS
REALFLIGHT DONGLE EMU FLAPS MANUAL
REALFLIGHT DONGLE EMU FLAPS SOFTWARE

Use your Display Modes ( Zero 0 ) to show the SAFE | AS3X options in response to your switch (B) on the Sim.Д¬ontact Spektrum, or Horizon Hobby, etc ( wherever you purchased your plane ) and report the issue with SAFE|bind failure. for E-Flite planes that have SAFE, select is on (B) position 0 is SAFE, position 2 & 3 are AS3X.

REALFLIGHT DONGLE EMU FLAPS MANUAL

Read your manual that came with the plane it will have special instructions for binding with SAFE on, and for setting SAFE select if equipped. Once bind mode is set (and on) you can check it by rolling or pitching the plane by hand (have the prop off) and watch the control surfaces they will move automagically to try to correct for your roll pitch. Keep in mind, most planes with SAFE and|or AS3X must be sitting up-right and level to setup SAFE and bind. An example is the Carbon Z Cub SS after the bind with SAFE, the desired switch is toggled (5) times to set the SAFE select option. Some planes you must assign a switch for SAFE select, once you bind in SAFE mode. Some planes have SAFE select (once bound) selectable based on firmware (you don't have to assign a switch, its built-in). If you bind with SAFE its on and stays on, if not then something is wrong in the receiver. Remember, nothing substitutes for reading the manuals.ДЄs for your plane coming out of SAFE for no reason that cannot happen unless you have SAFE select enabled and you're bumping the switch. If you have issues or other questions please let me know. Hopefully, you'll be able to follow this enough to do what is necessary on your DX8e. Once I got my flaps and SAFE select to work I quit screwing around with it. It should be possible to setup the Sim controller (Spektrum (7+ch) ) to accept what the DX8e is sending, by default, but I have not attempted that yet. My DX8G2 has a physical knob on the aux channels that I'm not using on any channel (inhibited) since I use the knob for voice volume on the DX8G2 (DX8e doesn't have voice). The DX8 Aux2 (knob) is inhibited, and Aux3 ->Aux2 is being used (D) for flaps ( essentially channel 8 ). The big picture again is that the DX8 Aux1 (channel 6) is being used (B) for Sim SAFE select. This way has worked for me, your mileage may vary (again, I have the latest DX8G2, latest firmware)ДЄlso, I don't know if your DX8e has a knob? Cosmetic.

(3) some planes with flaps will work on (D), not all.ДЄgain, keep in mind, you can setup your DX8 and use the eight channels any way you want to, there isn't just ONE right way. (2) most of the E-Flite planes (no SAFE) will work. (1) most of the E-Flite planes (with SAFE) will work.

( and rename it Generic Sim (SAFE) )-ДЄt this point the Generic Sim (SAFE) model will be saved and can now be used with the Rf9.5 Sim, with the following caveats: (assumed standard airplane model created). We will setup the DX8e to match what the Sim expects. Use the Sim controller Spektrum Receiver (7+ch) selection in Rf9.5 under Simulation | Select Controler, and leave (use) the defaults for this setup. How you decide to do that is up to you, but is important because you must be consistent. also you can accomplish an equivalent solution by adjusting the Sim or the DX8e. These are the detailed instructions following first be aware that there are several ways to accomplish the same thing, and my solution is just one way. I inhibit my AUX2, and set my AUX3 channel to be AUX2 and put it on switch D. I set my SAFE select on AUX1, and set it to switch B. I make a model in my DX8G2 (the following should also work in the DX8e, or be close) called Generic Sim (SAFE). What you need to do is set the DX8e switches and channels to get your SAFE select (B) and your Flaps (D) setup.

REALFLIGHT DONGLE EMU FLAPS SOFTWARE

The software radio of Rf9.5 Sim (hereafter Sim) is setup with the flaps on channel 6, activated by default with a knob.

REALFLIGHT DONGLE EMU FLAPS MANUALS

I'm going to answer your question as best I can, but first some caveats, or assumptions, that you should be aware of: (1) study the controller selection|setup in Rf9.5 (2) study the digital switch | channel selection sections of the DX8e (3) be willing to read the manuals for both Rf9.5, and the Spectrum DX8e.

Realflight dongle emu flaps